Ford Differential. Ford Differentials Exchange.

Ford Differentials,
Ford Drive Axle, Ford Axle.
All Ford models available for delivery or shipped World wide.

Ford 10.25 and 10.50 Differentials.
• Bearing & Seal Kits
• Cases, Aluminum, Iron, Stock & Aftermarket
• Pinion Yokes
• Posi Units, Carriers and Parts
• Ring & Pinion Sets
• Shims, Spacers, Bolts and Related Parts

Ford 7.5 Ford Differential.
• Bearing & Seal Kits
• Cases, Aluminum, Iron, Stock & Aftermarket
• Pinion Yokes
• Posi Units, Carriers and Parts
• Ring & Pinion Sets
• Shims, Spacers, Bolts and Related Parts

8 Inch Ford Differential.
• Bearing & Seal Kits
• Cases, Aluminum, Iron, Stock & Aftermarket
• Pinion Yokes
• Posi Units, Carriers and Parts
• Ring & Pinion Sets
• Shims, Spacers, Bolts and Related Parts

8.8 Ford Differentials.
• Bearing & Seal Kits
• Cases, Aluminum, Iron, Stock & Aftermarket
• Pinion Yokes
• Posi Units, Carriers and Parts
• Ring & Pinion Sets
• Shims, Spacers, Bolts and Related Parts

9 Inch Ford Differential.
• Bearing & Seal Kits
• Cases, Aluminum, Iron, Stock & Aftermarket
• Pinion Yokes
• Posi Units, Carriers and Parts
• Ring & Pinion Sets
• Shims, Spacers, Bolts and Related Parts

Ford 9.75 Rearend, Differential.
• Bearing & Seal Kits
• Cases, Aluminum, Iron, Stock & Aftermarket
• Pinion Yokes
• Posi Units, Carriers and Parts
• Ring & Pinion Sets
• Shims, Spacers, Bolts and Related Parts

The Ford 7 1/4 inch integral carrier differential used in light duty applications like the six cylinder Falcon, Comet, Mustang, and Fairlane. This is called an integral carrier differential because the differential is an integral part of the axle housing. Axle ratios are 2.83:1, 3.00:1, and 3.20:1. Most common are 2.83:1 and 3.20:1. If you want economy, use the 2.83:1 ratio. If snap is more important, use the 3.20:1 ratio.

The most common Ford differential axle combo was the 8-inch removable-carrier unit. The differential bolts to the axle housing as a separate unit. The removable carrier is nicknamed the "pumpkin," "chunk," or "third member" .
It has an 8-inch-diameter ring gear. Available ratios are 2.79:1, 2.80:1, 3.00:1, and 3.25:1.

The Ford 9-inch differential, removable-carrier rear axle. Like the 8-inch unit, the 9-inch is a two piece axle with a removable differential carrier. The 9-inch axle was produced a variety of ways for Ford's heavier duty applications, fullsize Galaxies, pickup trucks, and big-block V-8 automobiles. Axle ratios range from 2.55:1 to 4.30:1 from the factory.

7- 1/4 Ford Differential.
• Bearing & Seal Kits
• Cases, Aluminum, Iron, Stock & Aftermarket
• Pinion Yokes
• Posi Units, Carriers and Parts
• Ring & Pinion Sets
• Shims, Spacers, Bolts and Related Parts

The Ford 7.5-inch integral-carrier rearend used in the 74 - 78 Mustang II and the 79- 84 Fox body Mustangs. Like the Ford 7-1/4-inch axle the 7.5 has the differential and axle housing in one unit.

Ford 8.8 differential, rear end. We offer the full line line of rear end parts for the Ford 8.8 inch differential. This differential was utilized by Ford as early as 1981 in the F-100 pickup, Broncos in 1981 to 1984, E-150 Vans starting in 1983. Mercury's including Capri and Cugars starting in 1986. Ring Gear DIAMETER 8.8", 10 7/16" X 20 RH THREADED BOLTS. PINION DIAMETER 1.626" 30 SPLINE, Cover Bolt Ft. Lbs. 28-38, Pinion Brg. Preload In. Lbs 16-29, Pinion Brg. Preload In. Lbs 8-14 Used, Ring Gear Backlash .008-.015, Ring Gear Bolt to case Ft. Lbs. 70-85, Side Brg. Caps Ft. Lbs. 70-85

12 bolt rear cover with 10.25" ring gear. most applications were full floating however some applications do have C-clip axles. Differentials older than 1993 will require a new yoke to be compatible with a new ring and pinion.

We offer a complete line of rear end parts for the Ford 9.75" differential. High quality ring and pinion sets in all ratios. High quality bearing rear end bearing overhaul kits including pinion bearings, pinion seal, crush sleeve, pinion nut, shims, ring gear bolts, marking compound and gasket. Including after market and OEM gear sets. Specifications:
R.G. Diameter 9.75", 12-12MM x 26 RH Threaded
Pinion Diameter 1.970 31 Splines, 12 Bolt Cover

(888) 9-4-GEARS
(888) 944-3277